Skip to main content

"Blinky" TDOA RDF Detector

Our local Amateur Radio club is building a Radio Direction Finding TDOA (Time Difference of Arrival) detector that has LED's to indicate the direction (Left or right) of the fox. 

Here are the build instructions.  

(Note: this project was originally presented by NZ1J.  See his video:  https://www.youtube.com/watch?v=mNqUKYkifOo&t=68s  )

Here is the completed project:



We start with the schematic:  

Note that you either install PIN Diode pairs s D3 and D2, or Diodes pair D1 and D4.   The difference between these is the packaging.  If you are ok with Surface mount, then install D1/D4.  If you want discrete components use D3/D2.

Next is the PCB.  



The PCB can be ordered using the GRBR files available from the author. 

The BOM for the electronic parts is as such:

  • Doppler Direction Finder Bill of Materials   11/12/2021
    •        Qty Part Digi-key Part Number References
      • 1 PIC Pocessor PIC16F18324-I/P-ND U1
      • 1 14 Pin Socket ED3114-ND U1
      • 1 78L05 497-7268-ND U2
      • 2 2N3904 2156-2N3904-FS-ND Q1, Q2
      • 2 PIN Diode 568-1922-1-ND D1, D4
      • 4 Green LED C503B-GCN-CY0C0792CT-ND D5, D6, D8, D9
      • 1 Red LED C503B-RCN-CW0Z0AA1-ND D7
      • 4 1k Resistor 1.0KQBK-ND R3, R6, R13, R17
      • 8 4.7k Resistor 4.7KQBK-ND R2, R5, R10, R11, R12, R14, R15, R16
      • 2 470k Resistor 470KQBK-ND R1, R4
      • 1 220pF Cap 399-14053-1-ND C6
      • 1 0.01uF Cap 399-9772-ND C5
      • 3 0.1uF Cap 399-4264-ND C1, C3, C4
      • 1 10uF Cap 493-17435-1-ND C2
      • 1 1uH Inductor 78F 1R0K-TR-RCCT-ND L1
      • 1 Slide Switch 450301014042-ND SW1
      • 1 9V Battery Clip 36-232-ND TP+
      Assembly Overview:

      Radio Frame parts:




       

      Comments

      1. how is the coil connected to the board, do you have to solder a wire to each end of the coiled wire?

        ReplyDelete
        Replies
        1. Yes, The simplest way is to solder the coiled wire to the PCB. If you wanted to add a jack or terminal strip you could.

          Delete
      2. Good idea, congratulations. In my case, there are always several signal sources (GSM, high-power TV and others), so I must to expand the antennas to one frequency :(
        Is there a chance for the system to work at 1.6 GHz? Theoretically, this is possible for any frequency. Has anyone tested at high frequency?
        73' de SP4IZK

        ReplyDelete
        Replies
        1. This device was designed by NZ1J. He could perhaps help you with this question. For me, I would build a simple TDOA (without the blinking lights) which would work at any frequency. The Simple TDOA that I am thinking of is just a 555 timer that switches the antenna using pin diodes. It is up to you to attach a radio and process the signal. This works great and I find it much easier to use.
          See https://aerobatgeek2.blogspot.com/2022/03/radio-direction-finding-tdoa.html and http://www.146970.com/PDFs/TDOA%20Phasenpeiler.pdf .
          .

          Delete
      3. Thank you for the quick reply.
        The amplifier in this scheme amplifies low-frequency signals. TRX is used to obtain the signal. Have there been any attempts to use a simple signal detector (Ge diode + capacitor)? Then TRX is not needed. If there is only one source nearby.
        There remains the problem of eliminating other sources. SAW filters are still expensive :(
        73' de SP4IZK

        ReplyDelete

      Post a Comment

      Popular posts from this blog

      Radio Direction Finding - TDOA

      This article describes a few projects that I built from plans for Amateur Radio Fox Hunting. Basically, the hobby/sport is for someone to hide a few low power "Foxes", which are small transmitters that beep or send Morse Code, and then have a bunch of HAM's try to find them. The first project that I built was a Yagi Antenna (Directional receiver) and a 4MHZ Offset Attenuator.  The attenuator is needed when you get close to the fox and you need to reduce the power of the received signal.  I struggled with this setup because, on my first 2 fox hunts, there was too much reflection and multi-path interference.  This causes false direction detection and if you are not mentally prepared for this, you want to throw all of your equipment into a garbage can and take up a different hobby.   There are some truly strange individuals who find this frustration fun and enjoy making other people suffer, but I will leave that discussion for another day.  Anyway, in one particularly frustr

      Internet Explorer 11 (Windows 8.1) "Google Bug". Back Button hangs IE

      I discovered this week that there is a bug in Google's web page that causes Internet Explorer 11 to hang when you click the back button. The specific scenario is that when you start on Google's web page, and go to a link of some sort, it can trigger this bug when you click back to return to google.  This is fairly well documented on some forums, in that it has been like this for a while, and Google seems unwilling, or unable, to modify their code to not trigger this bug. I do not consider it a IE11 bug as much as I consider it a problem with Google.  Microsoft should of course fix their issue, but also you would think that Google might take this seriously.  To trigger the issue, Go to google.com and search for something that takes you to a Microsoft page.  Example: "Exchange edge server".  Click on the first link and then click on any link on that Microsoft page.  Then click back twice.  The first "back" will work fine because it takes you to the original Mi